| Official Luthiers Forum! http://www-.luthiersforum.com/forum/ |
|
| Ovation refret with aluminum fingerboard? http://www-.luthiersforum.com/forum/viewtopic.php?f=10137&t=53040 |
Page 1 of 1 |
| Author: | Tim Mullin [ Tue Mar 24, 2020 6:54 pm ] |
| Post subject: | Ovation refret with aluminum fingerboard? |
Ovations are not too popular around here, but every once in a while one shows up. The week before I was forced to close for C-19, I had no less than 3 to evaluate! The third one through was quite unlike any guitar I’d ever seen, with a strange headstock and a black-painted ALUMINUM fingerboard! The fingerboard was slightly wider than the neck itself and during my short inspection, I didn’t identify a truss rod adjuster, just two neck attachment bolts (I think). Someone had played the heck out of this guitar and the frets were thoroughly munched (and aluminum showing where the black paint was worn off). Looks like they had been leveled at some point, but no crowning. The fellow asked me how much to refret? I hedged, quoting my usual rate as a starting point, if it was possible at all, and a likely up charge for difficulty. Anyone ever managed a refret on such a beast? How? PS: I frightened all three Ovations out of the shop with my estimates! Sent from my iPad using Tapatalk |
|
| Author: | Chris Pile [ Tue Mar 24, 2020 7:18 pm ] |
| Post subject: | Re: Ovation refret with aluminum fingerboard? |
Is it an Applause (black plastic peghead overlay), or an Ovation? No matter…. I used to sell those way back in the late 70's. In fact, sold an Applause to my brother. He finally wore the frets down to nothing, and it played and sounded horrible. You couldn't bend strings on it at all. Near as I can tell - impossible to fix. The fingerboard on the Applause was cast integrally with the neck. It had 2 stripes down the back of the neck - filled with brown foam which eventually chipped out. You didn't dare play it in the sun because it wouldn't stay in tune. The aluminum was kind of gummy as I remember. Not one of Kaman's great ideas. |
|
| Author: | B. Howard [ Wed Mar 25, 2020 6:10 am ] |
| Post subject: | Re: Ovation refret with aluminum fingerboard? |
Those frets are cast as part of the fretboard itself. I have leveled and re-crowned a few over the years but a re-fret is a non starter. Might be able to replace the finger board but the instrument isn't really worth the expense and effort. |
|
| Author: | jfmckenna [ Wed Mar 25, 2020 8:37 am ] |
| Post subject: | Re: Ovation refret with aluminum fingerboard? |
Nothin' but a canoe paddle at that point. |
|
| Author: | Jim Watts [ Wed Mar 25, 2020 12:58 pm ] |
| Post subject: | Re: Ovation refret with aluminum fingerboard? |
I always thought a pair of those might make interesting speaker boxes for the shop. |
|
| Author: | Tim Mullin [ Wed Mar 25, 2020 3:48 pm ] |
| Post subject: | Re: Ovation refret with aluminum fingerboard? |
Really quite an unusual critter — certainly new to me. Thanks for all the comments! Sent from my iPhone using Tapatalk |
|
| Author: | Ruby50 [ Wed Mar 25, 2020 5:26 pm ] |
| Post subject: | Re: Ovation refret with aluminum fingerboard? |
My 83 year old uncle bought this soprano banjo uke in 1950 - his first of now many. It came with colored strings and "easy instructions" but it took with him. Nylon strings so no fret wear to speak of. He passed it on to because I always have admired it. |
|
| Author: | Chris Pile [ Wed Mar 25, 2020 6:32 pm ] |
| Post subject: | Re: Ovation refret with aluminum fingerboard? |
One of my nephews has one of those. From the age when American industry said "We can make any dang thing, just because we want to!". |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|